Questions tagged [pset4blur]

The tag has no usage guidance.

Filter by
Sorted by
Tagged with
1
vote
0answers
8 views

pset4 filter - only blurs the corners correctly

i can`t get the picture blurred at all (it comes out a complete mash up of colours blended together ...) ...i' ve been trying to figure this out for months now :(( HELP! void blur(int height, int ...
0
votes
0answers
7 views

Pset4-Filter Blur function doesn't pass check50. What's wrong?

I have been working on this function for about a week and have tried multiple ways, I have come up with a code that seems right to me but it presents errors when using the check50. This is the code I ...
0
votes
0answers
12 views

Pset4 - filter Blur

I wrote following code for blur filter . But I can't get the positive result . I want to know what the mistake is . void blur(int height, int width, RGBTRIPLE image[height][width]) { ...
0
votes
1answer
38 views

pset4 filter/blur code problem

I have written code for the blur filter in problem set 4. The code compiles and runs fine and seems to blur the image but when I run check50 it says that the RGB values aren't correct. I have looked ...
0
votes
0answers
41 views

FILTER WORKS FINE, BUT BLUR FAILS 3x3 and 4x4

The code works fine, but it fails blur filters a 3x3 and 4x4 image. I would like a help on why it correctly blur a middle pixel, but fails those two. Apparently, the wrong pixels are either on edge (...
0
votes
1answer
76 views

pset4 filters: thinking behind blur

Need some help with blur. I think i'm getting it entirely wrong but i can't seem to understand why. None of the blur assessment are correct at all. Wonder if anyone can give me any tips on getting the ...
0
votes
1answer
37 views

What is wrong with my filter blur?

Been stuck on the blurring part for ages... I've ran out of ideas and motivation to debug at this point after spending an eternity cutting down my spaghetti codes to pappardelle. Any help/hint/...
0
votes
1answer
44 views

Pset 4 Filter - Blur

My blur filter produces a decent looking blurred image and passes the Check50 corner pixel case. I define the cases for the edges and the middle pixels and then manually calculate the average RGB ...
0
votes
0answers
14 views

Why does the code output incorrect amounts?

The code is here: https://pastebin.com/gKnVmPFf I've checked that it's not because of neighboring cells, because I am translating them onto a different array. I can't seem to figure out want is wrong. ...
0
votes
1answer
23 views

Pset4-Blur function edge value issue

The edge value of blue is getting increased by 3, can someone help me Expected Output: 80 95 105 Actual Output: 80 98 105 // Blur image void blur(int height, int width, RGBTRIPLE image[...
0
votes
1answer
124 views

PSET 4 Filter (less) - Simplification of code for blur

My programme works, it compiles well and it passes the check50 checks. However, I don't like how it looks - I feel it's very cumbersome, too full of logical conditions. I was wondering how I might ...
0
votes
0answers
17 views

The blur is not updating when it should be

The suspected incorrect of my code is here: for(int i =0;i<height;i++) { for(int j = 0;j<width;j++) { image[i][j] = copy[i][j]; } } or ...
0
votes
1answer
55 views

CS50 Blur Problems

:) blur correctly filters middle pixel :) blur correctly filters pixel on edge :) blur correctly filters pixel in corner :( blur correctly filters 3x3 image expected "70 85 95\n80 9...", not "...
0
votes
0answers
38 views

cs50 pset4 ffilter reflection and blur stuck

I can't get up with a way to implement the code for reflect and blur particularly how to swap pixles in reflection, i tried use temp array as in lecture 4 but i couldn't, and in blur i could not get ...
0
votes
2answers
19 views

Blur function doesn't work properly in 3x3 and 4x4 case

I think it's happened during neighbors cell check. I adapt the code from Java stackoverflow. The first two pixels got the rest void blur(int height, int width, RGBTRIPLE image[height][width]) { //...
0
votes
2answers
1k views

PSET4 Filter: Blur help

While trying to create an algorithm to come up with the average of the color for all nine pixels (if using 9) I realized I would need a way to see how many surrounding pixels are used in the ...
0
votes
1answer
89 views

Blur error in CS50 problem set 4 — filter_less

I have been trying to figure out the error for hours long and still no success, it'll mean a lot to me if someone can tell me what is the error in this code in order to apply a blur filter. I ...